Firmware 1.1.59

[dainiuxsky]

1.1.59 have more serious bug:
Knock does not work fully
unstable working fuel injection
I suspect INJ0 very skinny 

tested Audi AAN 2.2 Petrol, N85, LPG

old vemstune has bug with alternative boost chanell. Allway was inj 0. So if you don't use, you can put treshold at 500kPa, or download new vemstune(today released)

1.1.61 incorrectly shows lambda, knock does not work anyway. 
Fuel Injection get back to normal   

[GintsK]

1.1.59 have more serious bug:
Knock does not work fully
unstable working fuel injection
I suspect INJ0 very skinny 

tested Audi AAN 2.2 Petrol, N85, LPG

Are your Audi is tuned on 1.1.5x previously? Or your first shot is on 1.1.59?
~~
Peep, I will send 1.1.53 ini, when access www from my tuning laptop.
~~
What i realy like in 1.1.59 is distributor ignition support witch was lost since 1.1.xx branch introduced.

Gints

Here is megatunes for 1.1.53-54
http://media.vems.se/code/

[PeepPaadam]

Thank you!

[AVP]

i have downloaded the vemstune,but whenever i try to open a config on a 1.1.56 firmware that i have installed, it pretty much crashes the laptop. Obviously im not connected to any ECU,but i want to make changes or build a config from scratch and i cannot!
what am i doing wrong?

[rob@vems.co.uk]

Which 1.1.x firmware, that works with MegaTune, would people use on a boosted 36-1 wasted spark system?

[PeepPaadam]

Which 1.1.x firmware, that works with MegaTune, would people use on a boosted 36-1 wasted spark system?

1.1.27 if no special features (nitrous control, speed sensor etc) are needed.

[rob@vems.co.uk]

And if I wanted the special features?  This car will want speed dependent boost to save the box from emptying its guts on the floor.

[MWfire]

Which 1.1.x firmware, that works with MegaTune, would people use on a boosted 36-1 wasted spark system?

1.1.47v2 is best version if is needed good boost cotrol(rpm and gear).
And has nitro, extended misc out .....
Very stable version(i use that verision on 8 cars, one has more than 600HP)

[Tony C]

is 1.1.47 on the forum?
or is it on the wiki?

[rob@vems.co.uk]

It will be buried somewhere in the wiki surrounded by confusing text that leaves us all baffled as to a) what it actually is, b) what it actually does and c) if it actually works!

[Denmark]

I have also been looking at finding that version 1.1.47V2, but cant even fint V1 of that version.

Is that a version that still works with MT?.

Could there maybe be made a link to were it can be downloaded, as a complete working packede.?

Am i the only one that thinks it really strange that there is none released firmware since. 1.0.73,
yet there have been written many times, that "release canditate , think we will release this"
more that ones over the last year or two, and the work just contienues, with 20 halv finished firmwares, were most if the change is a pure guess for the user..


/Skassa

[gunni]

You are not the only one.

[ryniobl]

Voila
http://195.159.109.134/vemsuk/forum/index.php/topic,717.30.html

I had the same problem as You guys.
Finally I found it,not so far away...

[MWfire]

Two notes:).
1. boost pwm table is gear dependeing. So 1. row(looking from bottom) is first gear, 2. row=2. gear...
rpm are rpm . These values are DC ref position for boost solenoid. So if you put p=d=i=0, you have opel loop boost controler depending on rpm and gear(no influence of boost target table).
You can make closed loop
2. in 12x12 version on firmware there is error with tps/boost scale. value for 62.5% tps is for 12.5% tps.
and value for actually 62.5% tps is in the botton left corner of boost pwm table, 75% one cell right...
16x14 doesn't have that problem

I made magatune for 12x12 for my customers where is easy to set boost dc and tps scaling, but i didn't test it much(warning are normal . I use v2, but v3 is good to see how to fill up tables(don't fill first 4 values in 1 gear).
http://www.sendspace.com/file/hylb3v