Author Topic: Has anyone seen lambda readings in a log file, but no ego correction happening?  (Read 97677 times)

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
No probs.
it looks like tomorrows show is the only one until around 3 weeks time,
you want me to put me .msq file on a 3.5 floopy and send to?
also you want to email me the address etc to send it back to mate please,

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
YHPM

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Jorgen.
I understand Rob has talked to you regarding the possible split inductor in my vems,:
would this cause the said spikes we are seeing?
and/or what else would it upset within the ecu,
it's being sent back to Rob this week, but curious to find out what it would upset within the ecu.

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
well the ecu is now speeding its way back to Rob.

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Well the ecu has been repaired,  ;D
Not sure 100% what was wrong, but Rob has replaced a few things on the board,  :o :o

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
The datalog before the repair looked like this:
http://www.vems.co.uk/VEMSInstalls/TonyCooper/TC1.xls

And after repair and reconfiguration:
http://www.vems.co.uk/VEMSInstalls/TonyCooper/TC3.xls

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Rob,
one thing i have noticed with the logs have you?
or am i pissing up a wall  ::)

before the rpm peaking at 25550 which is what i had this end,
then after 5000 max,
could we of solved the ferkin spiking fault at last as well as the ego???

thanks again for this mate,
can i put the alternator and bits back in the car now as it may not of been the cars fault after all  :D :D

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
 ;D ;D ive got ego ive got ego ive got ego  ;D  ;D

not sure if you are aware rob the ego is working mate  ;) ;D :D

in the lambda control mate the rich and lean settings,(10% your settings) is that how high or low the lambda will go before the ecu does correction?

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
just has a quick peep at the settings mate,
did you reset my temp table? as im using the rover temp switch mate,
and dont look like what i thought they were before the ecu was sent away mate.

and in settings->EGO(lambda) control:
ego nbo2 connected is set to disable
ego nbo2 pid config is set to enabled
does that matter?

EDITED>>>>>
and the datalog to go with tonights start up,
www.v-8.org.uk/zipfiles/log03_04_08.zip
« Last Edit: April 03, 2008, 10:13:01 pm by Tony C »

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Didnt touch those temp settings as far as I can remember.

As for the NBO2 section - if its disabled the other setting is ignored.

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
cheers Rob,
i'll see if i still have the old .msq i can look at,

also in the lambda control mate the rich and lean settings,(10% your settings) is that how high or low the lambda will go before the ecu does correction?

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
They are to limit the maximum % of adjustment.  The idea is that you should be within 10% of the target mapping by hand (in reality you should be within 2% to 5%).

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
cheers mate,
once the throttle cable arrives i'll take her for a run and do a log to see how she is setup wise on the VE and pop it on here,
cheers for your help Rob,
next will be ignition mate :D

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Cable arrived,
took for a run, still have them spikes now and then so need to look into that a bit more,
Rob, could the tach output on the cdi be playing up?
can i connect to the -neg side the coil instead of the cdi box to see if we still get any spikes?
or wont it work with my settings?

here is todays datalog along with .msq
www.v-8.org.uk/zipfiles/log04_04_08.zip

now can some one help with tuning the lambda readings now please, :D :D
any one got a program for this?
i did kangaroo while on light throttle and i think the engine actual lambda went real lean, think it was 4% throt around 2kish rpm towards end log

and forgot to say the car ran defo smoother Rob,
so the repairs have done some good mate, thanks.  ;)
« Last Edit: April 04, 2008, 07:41:31 pm by Tony C »

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
I wouldn't connect anything to the side thats driven by the CDi, its likely to kick out huge voltages.

Theres no substitute for getting the fuel mapped properly, EGO will only do so much.

http://www.vems.hu/wiki/index.php?page=TuningSession%2FClosedloopTuning