No Wideband readings with firmware 1.2.32

[black]

VEMS 3.6 AAN PNP with firmware 1.2.32, VemsTune 1.5.30, LSU 4.2

When starting engine, wideband in VemsTune shows 1.83.

After sensor is heated up, wideband in VemsTune shows 0.65.

Zeitronix shows 0.91.

Changing sensor = same result 

before firmware update everything was fine...

[VEMS]

Hello Black,

After downgrading firmware to 1.2.30 (from 1.2.32), does wideband work again ?
In that case i would be very interested to see your 1.2.32 config, please make a bugreport/sharing report; Reports without any additional data are very hard for me to review.

Best regards, Dave

[black]

Hello Black,

After downgrading firmware to 1.2.30 (from 1.2.32), does wideband work again ?
In that case i would be very interested to see your 1.2.32 config, please make a bugreport/sharing report; Reports without any additional data are very hard for me to review.

Best regards, Dave

Report is coming soon.. But when I downgrade do 1.2.30 what will happen with my tables axis because I am using the 700kPa setup (factor 4 in map calibration)...

[VEMS]

Report is coming soon.. But when I downgrade do 1.2.30 what will happen with my tables axis because I am using the 700kPa setup (factor 4 in map calibration)...

In 1.2.30 factor = 4 was not supported so it would make sense to load some 1.2.30 (i hope you saved one) from before for this small test.

Best regards, Dave

[black]

Report is coming soon.. But when I downgrade do 1.2.30 what will happen with my tables axis because I am using the 700kPa setup (factor 4 in map calibration)...

In 1.2.30 factor = 4 was not supported so it would make sense to load some 1.2.30 (i hope you saved one) from before for this small test.

Best regards, Dave

ok, I will have a look at this... 

PS logfile sent via PN

[black]

Tried to do a new config file from the .32 log I sent you. (ECU disconnected)

LSU in Wideband settings is 4.2 / 4.2 in logfile like it should be

- Saving config file from logfile

- Closing VEMSTune

- Starting VEMSTune again

- Loading previous saved config file

- LSU is now 4.9 / 4.9 ... should be still 4.2 / 4.2 

- changing to 4.2

- saving

- Closing VEMSTune

- Starting VEMSTune again

- loading saved config file

- and again - 4.9 

Config safe from ECU:

fix_retard[0]=80
fix_retard[1]=80
fix_retard[2]=80
fix_retard[3]=80
fix_retard[4]=80
wbo2_pump_pw_zero2=65
wbo2_nernstdc_target2=85
wbo2_calibration2=00
ibutton_code2[0]=64
ibutton_code2[1]=A8
fuelcut_delay=01
iac2etctarget=00
wbo2_ri_target2=AF
wbo2_config=C0
h[0]=01 02 04 08 10 20 40 80
h[1]=00 60 48 30 18 FF FF FF
h[2]=68 40 38 48 58 50 50 50
h[3]=00 00 00 00 00 00 00 00
h[4]=80 80 80 80 80 80 80 80
h[5]=00 00 00 00 00 00 00 00

ECU offline, config safe from log or from previous config:

fix_retard[0]=80
fix_retard[1]=80
fix_retard[2]=80
fix_retard[3]=80
fix_retard[4]=80
wbo2_pump_pw_zero2=65
wbo2_nernstdc_target2=85
wbo2_calibration2=00
h[0]=01 02 04 08 10 20 40 80
h[1]=00 60 48 30 18 FF FF FF
h[2]=68 40 38 48 58 50 50 50
h[3]=00 00 00 00 00 00 00 00
h[4]=80 80 80 80 80 80 80 80
h[5]=00 00 00 00 00 00 00 00

No WBO2 config anymore ?

[VEMS]

Hello Black,

That are some good hints you provided there, it seems you have a earlier compile of 1.2.32 in your VT directory (remember 1.2.32 is still experimental and had multiple iterations) . Please follow these steps:

1) browse into VT_install_dir/vemsprojects and remove firmware_1.2.32 dir
2) browse into VT_install_dir/webcache/fw and remove  v3_firmware_1.2.32.zip
3) re-download 1.2.32 from DEV server: http://svn.x-dsl.hu/f/v3_firmware_1.2.32.zip and copy to VT_install_dir/webcache/fw dir
4) start VT, update ini's from web
5) in VT firmware webtool, reinstall 1.2.32
6) upload load this new 1.2.32 firmware to your ecu and upload config.

I suspect there was a mismatch between the firmware in your ecu (some older 1.2.32 version) and the latest ini's from web, which are always for the last (to be released) version. We have many cars running 1.2.32 out there (both LSU 4.2 and 4.9), so rest assured there is no actual wideband problem in firmware.

Best regards, Dave

[black]

Hello Black,

That are some good hints you provided there, it seems you have a earlier compile of 1.2.32 in your VT directory (remember 1.2.32 is still experimental and had multiple iterations) . Please follow these steps:

1) browse into VT_install_dir/vemsprojects and remove firmware_1.2.32 dir
2) browse into VT_install_dir/webcache/fw and remove  v3_firmware_1.2.32.zip
3) re-download 1.2.32 from DEV server: http://svn.x-dsl.hu/f/v3_firmware_1.2.32.zip and copy to VT_install_dir/webcache/fw dir
4) start VT, update ini's from web
5) in VT firmware webtool, reinstall 1.2.32
6) upload load this new 1.2.32 firmware to your ecu and upload config.

I suspect there was a mismatch between the firmware in your ecu (some older 1.2.32 version) and the latest ini's from web, which are always for the last (to be released) version. We have many cars running 1.2.32 out there (both LSU 4.2 and 4.9), so rest assured there is no actual wideband problem in firmware.

Best regards, Dave

Thanks we will test this.

by the way, 1.2.30 LSU works...

regards

[black]

Ok,

now wideband is running with 1.2.32...  thanks a lot 

regards...

[VEMS]

Hello Black,

Glad to hear its sorted now, sorry for the mixup.

Best regards, Dave

[black]

Hello Black,

Glad to hear its sorted now, sorry for the mixup.

Best regards, Dave

Still issues - did you notice my last logfile (PN)?

regards

black

[black]

After days of testing we have still issues...

...wideband sometimes takes 10 Minutes before showing values with the last .32 

[VEMS]

Hello Black,

After days of testing we have still issues...
...wideband sometimes takes 10 Minutes before showing values with the last .32 

I missed your latest comment, i'll locate your sharing report and take a look. note: sharing reports are not automatically reviewed unless explicitly linked from wiki/forum thread or email with a description of problem/data on what needs to be reviewed.

Best regards, Dave

[black]

Hello Black,

After days of testing we have still issues...
...wideband sometimes takes 10 Minutes before showing values with the last .32 

.... note: sharing reports are not automatically reviewed unless explicitly linked from wiki/forum thread or email with a description of problem/data on what needs to be reviewed.

Best regards, Dave

I know, I know but I sent you a PN here with a link to my newest sharing report - maybe it was lost somehow...  regards :-)

[s38turbo]

i have almost same problem with wideband, always when make first startup after car has stopped over night then wb dont show nothing , then i let it idle for 10 minutes and restart car and after that it shows lambda normally. also when its heated up and only iginition is on then its also showing lambda 1.00 or something .
problem began after installing 1.2.32