VemsTune for Android ?

[Pet]

So I've made some tests with different phones: (with HC-06 BT module of course)

 1] Samsung Galaxy Note II (4.1.2) - OK (connected in a few seconds without problems)
 2] Lenovo P770 (4.1.2) - KO
 3] Lenovo A660 (4.1.1) - KO
 4] ZTE V970S (4.0.4) - KO
 5] Lenovo A820 (4.0.4 - MTK6589 - quadcore) - KO
 6] ZTE 967S (4.2.1 - MTK6589 - quadcore) - KO
 7] Galaxy Tab II (10.1") - OK
 8] Alcatel OT-997D (4.0.4 - MTK-6575) - KO

So as I've said, there is probably some VemsDisplay apk HW incompatibility, now I can say it for sure.
All Lenovo's and ZTE have MTK6577 CPU. Maybe this is the problem.
If developers want, I can make some extra tests....

14.10.13 - Edit: two more phones tested (both quadcores MTK6589) - not running on both
18.10.13 - Edit: Tested on Galaxy Tab II tablet - works without problems + Alactel OT-997D - not works

[VemsedE36]

Pet..did you get egt reading with note 2?

[Pet]

Pet..did you get egt reading with note 2?

Sorry ecu was on the table and was no time to check it, maybe later.

[VemsedE36]

Very appreciated

[Pet]

Pet..did you get egt reading with note 2?

Sorry ecu was on the table and was no time to check it, maybe later.

So here is short Utube video from EGT1 test. AD Ch4 RAW is changing well (it means EGT1 is changing too in Vemstune), in Vemsdisplay not.
http://youtu.be/QigGBdsSCNw

[VemsedE36]

Ummm... I will try Samsung gs3 today...

[VemsedE36]

VemsDisplay on Samsung galaxy s4 and s3(china) works fine except EGT reading, so similar to Note 2..

[LHK_audi_S2_Nor]

Upgraded to fw 1.2.11 and runs triggerframe protocol, works very nice! Also logged data on the phone, exported log file to pc, converted and did VE tune by statistics in VEMS! I like it.. 

Does it EGT values in triggerframe mode?

My firmware is 1.2.11 but unable to get EGT value in triggerframe mode.

Anyone???

What vemsdisplay version r u using?

A bit late but:
No egt data (N/A is wat comes up in VemsDisplay)
VemsDisplay ver 3.0
Phone is Sony Erixsson Xperia LT15i Android version 2.3.4 (yes it's old :-))

[VemsedE36]

LHK_audi_S2_Nor Did you inform the developer?

[LHK_audi_S2_Nor]

No, I dont have an egt probe installed/connected so not important for my car. I THINK it should have presented "0 or whatever defaultvalue °C" instead of "N/A" if it worked.
Excuse the late reply..

[NitroX5]

Same here, no EGT value, shows N/A, others are fine... fw 1.2.11, Vems display 3.0,  Andro 4.2.2
It seems this should really be adressed to developers.

[PeepPaadam]

Resurrecting this thread.

I have bought a BT adapter from webshop and it works well, though with cheap HC-06 modules from ebay (with voltage regulator board and pins already in place) I cannot establish a connection. Pairs nicely with tablet, but no data from VEMS. Also cannot connect via terminal to change baud rates (default is 9600). Tried swapping Rx and Tx, still nothing.

I am aware of the short timeframe for sending commands but pasting also does not work. Any hints?

Module is typical arduino unit:

[MWfire]

that adapter need ttl with 3.3V, so you need to add max232 for 3.3v

Also that adapter has debug msg that corrupt config, so don't use that.

[mads b (dk)]

that adapter need ttl with 3.3V, so you need to add max232 for 3.3v

Also that adapter has debug msg that corrupt config, so don't use that.

Are you sure that vems dont have max232 ?
https://www.dropbox.com/s/kw1nn6w6uq3ergx/2014-07-10%2013.37.59.png

[PeepPaadam]

that adapter need ttl with 3.3V, so you need to add max232 for 3.3v

Also that adapter has debug msg that corrupt config, so don't use that.

I have TTL to RS232 converter but it did not work with that also. Regarding corrupting config, I thought that leaving Rx pin on VEMS side open would make it a moot point?