Author Topic: Audi 200 20vt on VEMS  (Read 8673 times)

Offline loxxrider

  • Jr. Member
  • **
  • Posts: 16
  • BHP: 1
Audi 200 20vt on VEMS
« on: August 15, 2009, 11:57:40 am »
Hey guys, thought it would be a good idea to document a little about this car in hopes of quick help, and some learning opportunities.

Most details about the car can be found here

http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FAudi

in short, firmware is 1.1.27

Ok, so the car is a 1991 Audi 200 20vt on stock turbo for now. The idea was to get the car running flawlessly on VEMS before going for a bigger Holset (H1C) and then something even bigger later

The basic setup is 5 individual high output coils from 034 Motorsport, VEMS v3.3, blah, blah...the car is very solid in almost every way...but this ECU has given me a bit of a headache so far.

A lot of the problems are outlined in that wiki page, but the most recent one involves "the AFR table values in Megatune changing to 15+ AFR by itself" and some backfiring issues upon onset of boost.

It seems that these motors are very picky with what plugs are used in them, so I switched them out today for a nice set, and it backfired once on the initial drive...then after that it made about 6 or 7 really strong and clean pulls.

I can post logs of that if needed, and can take more logs tomorrow.

The issue with the megatune is the most annoying though. I have tried using two different laptops, one with xp and one with vista. Sometimes when I try to mess with the tables when its not hooked up to the car, lambda values get randomly changed.

Then when I tried it with the ECU connected today, it turned the kPa and RPM values at the bottom and side of the table all go to zero...obviously when I burned this to ecu and tried to start the car, it had trouble running as it defaulted to the top right corner which had a value of about 11.5:1 AFR. It idled, but not correctly. I tried this multiple times with the same problem, and had to switch to my vista computer to put the right tune back in the car. Its the same exact file sent through e-mail.

Both computers occasionally pull up messed up tables though. I'd just like to get to the bottom of this issue.

There are screenshots in this thread here...

http://www.motorgeek.com/phpBB2/viewtopic.php?t=29275



Thanks in advance for any help!

Here is the build thread for this car if you are interested. Its pretty lengthy now...

http://www.motorgeek.com/phpBB2/viewtopic.php?t=21657

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: Audi 200 20vt on VEMS
« Reply #1 on: August 15, 2009, 12:57:50 pm »
Sounds like not computer or XP problem, but mismatch between vems ECU firmware and Megatune package. Every firmware version needs different files in tuning program too.
Safer way is download full package with Megatune and firmware from here:
http://www.vems.hu/wiki/index.php?page=MegaTune

Gints

Offline loxxrider

  • Jr. Member
  • **
  • Posts: 16
  • BHP: 1
Re: Audi 200 20vt on VEMS
« Reply #2 on: August 16, 2009, 01:33:19 pm »
Had another batch of issues tonight.

It did rain really hard, so I'm not sure whether it should be attributed to rain or more ECU problems.

The car was doing this back when it somehow got the wrong setting in the ecu for the H2 stuff. The top one was listed as stepper instead of ign. I haven't touched the ECU today and it just randomly started doing this.

First of all, it would lose RPM signal completely then just run like crap because its defaulting to a low afr value I assume. As soon as I cycle ignition power, its fine and runs perfectly again.

Also sometimes when cranking, RPM's will jump up and it will simultaneously sound like its out of time or something...just for a split second...then it will continue cranking and fire up.

I'll hook the ECU up in the morning and see if that H2 value got changed again somehow.

Offline loxxrider

  • Jr. Member
  • **
  • Posts: 16
  • BHP: 1
Re: Audi 200 20vt on VEMS
« Reply #3 on: August 16, 2009, 10:27:21 pm »
config download from about 30 seconds ago

# CurrentTime: 2009-08-16 11:23:33
# Version: 1.1.27
# SerialNumber: v3.3_n001883
# CompilationTime: Mon Sep  3 15:10:58 CEST 2007
# Signature: VEMS v1.1 12x12 kpa=2,2

primep=00
primep_temp_scaling=00
cwl=2D
cwh=14
cranking_thres=03
awev=69
awev_temp_scaling=4D
awec=11
warmup_clt_range[0]=00
warmup_clt_range[1]=00
warmup_clt_range[2]=00
warmup_clt_range[3]=13
warmup_clt_range[4]=50
warmup_clt_range[5]=64
warmup_clt_range[6]=78
warmup_clt_range[7]=8C
warmup_clt_range[8]=AA
warmup_clt_range[9]=C8
warmup_clt[0]=C8
warmup_clt[1]=C8
warmup_clt[2]=AA
warmup_clt[3]=8C
warmup_clt[4]=82
warmup_clt[5]=7D
warmup_clt[6]=78
warmup_clt[7]=73
warmup_clt[8]=6C
warmup_clt[9]=64
warmup_rpm_scale=A8
req_fuel=3C
divider=01
alternate=14
injopen=00
battfac=22
kpafac=D0
kpaoffs=90
injocfuel=19
injrampup_battfac=FF
injpwm=FF
injpwmt=FF
als_launch_input=0C
rpmk[0]=09
rpmk[1]=60
tpsdot_kpadot_conf=00
tpsdotrate[0]=04
tpsdotrate[1]=07
tpsdotrate[2]=0F
tpsdotrate[3]=1A
tpsaq[0]=04
tpsaq[1]=09
tpsaq[2]=0E
tpsaq[3]=14
als_cut_mintps=FF
tpsasync=1E
acmult=7D
tpsacold=14
launch_enrich=00
launch_retard=00
overrun_fuelcut=63
overrun_fuelresume=62
rev_limit=4A
airden_ignore=61
config11=41
config12=40
config13=02
batt_cal=C6
fastidle=C6
als_max_cut=00
dbaro=0A
tps_low=0B
tps_high=EA
fan_temp=EA
fan_hyst=05
fan_channel=FF
iac_step_seq=D8
iac_conf=58
iac_max_steps=FF
iac_tps_thres=05
iac_cold_idle_temp=63
iac_warm_idle_temp=B4
iac_cold_rpm=69
iac_warm_rpm=5A
iac_cold_start_pos=FF
iac_warm_start_pos=80
iac_afterstart_rpm=0A
iac_afterstart_duration=19
iac_speed=00
iac_kp=1E
iac_ki=1E
iac_kd=19
launch_rpm=2D
iac_integral_limit_dec=14
iac_integral_limit_inc=0A
iac_integral_deadband=19
iac_deadband=0A
als_cut_maxtps=FF
iac_overclose_interval=FF
iac_ref_pos[0]=BF
iac_ref_pos[1]=BA
iac_ref_pos[2]=AD
iac_ref_pos[3]=A8
iac_ref_pos[4]=A1
iac_ref_pos[5]=99
iac_ref_pos[6]=91
iac_ref_pos[7]=87
iac_ref_pos[8]=80
iac_ref_pos[9]=80
iac_sol_channel=60
iac_ign_slope=30
softrpm_range=0D
iac_ign_advance_limit=18
iac_ign_retard_limit=10
iac_ign_threshold=14
ego_conf=18
ego_lag=06
ego_coolant=B4
ego_maxtps=80
ego_maxmap=3F
ego_minrpm=62
ego_maxrpm=63
ego_warmup=63
ego_lean_limit=00
ego_rich_limit=00
ego_pid_kp=00
als_enrich=00
ego_delta=00
ego_target=00
ego_pid_window=00
wbo2_warmup_ramp=FF
als_react_tps=FF
wbo2_abs_limit=E0
wbo2_limit_maxt=F0
wbo2_fallback=70
wbo2_retry_t=06
als_retard_rpm1=FF
als_retard_rpm2=FF
wbo2_ri_target=A5
wbo2_nernstdc_target=89
wbo2_pump_pw_zero=63
wbo2_calibration=B4
wbo2_heater_pid_kp=45
wbo2_heater_pid_ki=11
wbo2_heater_pid_kd=1A
wbo2_heater_pid_ilimit=80
wbo2_pump_pid_kp=15
wbo2_pump_pid_ki=4E
wbo2_pump_pid_kd=00
wbo2_pump_pid_ilimit=FF
wbo2_ri_confidence_scale=80
knock_chan=00
knock_sampling_window=F2
knock1_frequency=29
knock1_gain=0E
knock1_integrator=14
knock2_frequency=29
knock2_gain=00
knock2_integrator=00
knock_threshold=0A
knock_noise_scale=D8
knock_max_retard=18
knock_default_retard=00
knock_retard_step=04
knock_retard_delay=30
knock_advance_step=01
knock_advance_delay=50
knock_minrpm=16
knock_maxrpm=42
ve_learn_coolant=CF
ve_learn_max_power=64
ve_learn_rpm_scale=28
ve_learn_kpa_scale=28
ve_learn_ego_scale=50
ve_learn_min_weight=14
ve_learn_speed=32
ve_learn_limit=80
ve_learn_conf=00
lcd_c0=FE
lcd_delay=42
lcd_backlight=FF
kpa_conf=22
als_igncut_rpm2=FF
als_retard_mintps=FF
als_retard_maxtps=FF
lcd_default_view=00
primary_trigger=43
secondary_trigger=19
tooth_wheel=5A
trigger_tooth=00
another_trigger_tooth=12
crank_minper=A3
tooth_wheel_twidth1=20
tooth_wheel_twidth2=00
cam_sync_r_edge_phase=00
cam_sync_f_edge_phase=00
reset_engphase_after=40
ign_tdcdelay=74
ign_dwell14=2B
ign_dwell6=13
ign_crank_advance=28
ign_out=70
ignchmax=04
engine_off_delay=02
pump_on_mintime=04
fuelpump_channel=50
inj_stage2_rate=FF
inj_stage2_start_tps=FF
inj_stage2_start_map=FF
als_igncut_rpm1=FF
als_deact_time=00
als_deact_egt=00
als_retard=00
als_rev_limit=63
misc1out_minrpm=FF
misc1out_maxrpm=FF
misc1out_mintps=FF
misc1out_maxtps=FF
misc1out_minmap=FF
misc1out_maxmap=FF
misc1out_channel=FF
misc2out_minrpm=FF
misc2out_maxrpm=FF
misc2out_mintps=FF
misc2out_maxtps=FF
misc2out_minmap=FF
misc2out_maxmap=FF
misc2out_channel=FF
act_wot_rpm=FF
act_wot_channel=FF
act_rpm_rpm=FF
act_rpm_channel=FF
egt1_cal=55
als_tks_channel=FF
boost_conf=29
boost_targetoffs=00
boost_minpressure=37
boost_pid_kp=FF
boost_pid_ki=14
boost_pid_kd=05
boost_pid_ilimit=7D
boost_channel=70
water_pump_temp=00
hybrid_rpm_a=00
hybrid_rpm_m=00
water_pump_hyst=7E
water_pump_channel=FF
toothrel_normal=76
toothrel_missing=00
fuelcut_min_kpa=09
fuelcut_max_kpa=85
tach_channel=07
tach_div=10
shiftcut_conf=01
shiftcut_channel=07
shiftcut_time=00
softrpm_rpm=48
# CurrentTime: 2009-08-16 11:23:40
# Version: 1.1.27
# SerialNumber: v3.3_n001883
# CompilationTime: Mon Sep  3 15:10:58 CEST 2007
# Signature: VEMS v1.1 12x12 kpa=2,2

j[0]=5E80 6380 6780 6980 6B80 6D80 7080 7380 7680 7480 7280 7080
j[1]=5F80 6480 6980 6C80 6F80 7280 7480 7680 7480 7280 7080 6E80
j[2]=6180 6680 6B80 7280 7480 7680 7880 7A80 7C80 7A80 7880 7680
j[3]=7380 7680 7E80 8080 8280 8480 8680 8880 8680 8480 8280 8080
j[4]=7880 7B80 8380 8580 8780 8980 8B80 8D80 8B80 8980 8780 8280
j[5]=7A80 7A80 7C80 7E80 8080 8780 8980 8B80 8A80 8880 8680 8380
j[6]=7E80 7E80 7E80 8080 8280 8480 8680 8880 8880 8580 8280 7F80
j[7]=8180 8380 8580 8780 8980 8B80 8D80 8F80 8F80 8D80 8B80 8980
j[8]=8480 8680 8880 8A80 8C80 8E80 9080 9280 9280 9080 8E80 8C80
j[9]=8880 8A80 8C80 8E80 9080 9280 9480 9680 9480 9280 9080 8E80
j[A]=8980 8E80 8E80 8E80 9080 9380 9380 9580 9580 9380 9180 8E80
j=8980 8E80 8E80 8E80 9180 9380 9480 9580 9580 9480 9180 8F80
l[0]=37 37 34 34 34 34 34 34 34 34 34 34
l[1]=37 37 37 34 34 34 34 34 34 34 34 34
l[2]=37 37 37 37 37 37 37 37 37 37 37 37
l[3]=44 44 44 44 47 48 48 48 48 48 48 48
l[4]=5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A 5A
l[5]=6B 6B 6B 6B 6B 6B 6D 6D 6D 6D 6D 6D
l[6]=73 73 73 73 73 7B 7B 7B 7B 7B 7B 7B
l[7]=73 73 75 7B 7B 7E 83 83 7E 7B 7B 7B
l[8]=7B 7B 7B 7B 7E 83 83 83 83 7E 7E 7E
l[9]=7B 7B 7B 7E 83 83 87 87 83 83 83 83
l[A]=7B 7B 7B 7E 83 83 87 87 83 83 83 83
l=7B 7B 7B 7E 83 83 87 87 87 83 83 83
n[0]=3C 48 5C 70 9C 9C 9C 9C 9C 9C 9C 9C
n[1]=3C 48 5C 70 98 98 98 98 98 98 98 98
n[2]=3C 44 58 6C 8C 8C 8C 8C 8C 8C 8C 8C
n[3]=3C 40 54 68 80 80 7C 7C 7E 80 82 84
n[4]=38 3C 50 64 78 74 70 70 74 78 7A 7C
n[5]=34 3C 50 5C 5C 58 54 54 58 5C 5C 5C
n[6]=30 3C 46 54 50 4C 48 48 4C 50 50 50
n[7]=30 38 3C 4C 44 42 40 40 42 44 44 44
n[8]=2C 34 38 44 3C 3C 3A 38 38 3A 3C 3C
n[9]=2D 33 38 40 3C 3C 3C 38 38 3A 3C 3C
n[A]=24 28 34 3C 3D 3E 3A 38 38 38 3A 3A
n=20 21 30 38 36 38 36 34 34 34 36 38
k[0]=0D 0F 19 26 32 4B 58 64 71 7D 8A 96
r[0]=09 0F 14 1A 20 26 2C 32 38 3E 44 4A
h[0]=01 02 04 08 10 20 40 80
h[1]=00 48 36 24 12 00 00 00
h[2]=10 70 60 30 20 50 50 50
y[0]=00 00 00 00 00 00 00 00 00 00 00 00
y[1]=00 00 00 00 00 00 00 00 00 00 00 00
y[2]=00 00 00 00 00 00 00 00 00 00 00 00
y[3]=00 00 00 00 00 00 00 00 00 00 00 00
y[4]=00 00 00 00 00 00 00 00 00 00 00 00
y[5]=00 00 00 00 00 00 00 00 00 00 00 00
y[6]=00 00 00 00 00 00 00 00 00 00 00 00
y[7]=00 00 00 00 00 00 00 00 00 00 00 00
y[8]=00 00 00 00 00 00 00 00 00 00 00 00
y[9]=00 00 00 00 00 00 00 00 00 00 00 00
y[A]=00 00 00 00 00 00 00 00 00 00 00 00
y=00 00 00 00 00 00 00 00 00 00 00 00


Offline loxxrider

  • Jr. Member
  • **
  • Posts: 16
  • BHP: 1
Re: Audi 200 20vt on VEMS
« Reply #4 on: August 17, 2009, 09:54:44 pm »
I did notice that all the Y's at the bottom are "0" instead of "FF"