Print Page - Rev limiter doesn't work (???)

Title: Rev limiter doesn't work (???)
Post by: jadzwin on January 27, 2009, 03:50:48 AM

Hello,

Please help 'cos I have no idea what is the problem (probably sth in configuration).

The car is Fiat Coupe 2.0 20V (5 cylinder).
I put Vems into this car during the week, but I can't set the rev limiter. Whatever I set the rev limiter (fuel cut) is always around 6500 (even I set rev limit to 3000)

Do you have any ideas (I use firmware 1.0.73) ?

Here is the msq file and log with rpm limit.
Any help / ideas will be appreciate.

http://www.ecumaster.com/lanos/fc/fiat_coupe.msq (http://www.ecumaster.com/lanos/fc/fiat_coupe.msq)
http://www.ecumaster.com/lanos/fc/fiat_coupe_rev_limit.xls (http://www.ecumaster.com/lanos/fc/fiat_coupe_rev_limit.xls)

Thank You
Jadzwin

Title: Re: Rev limiter doesn't work (???)
Post by: [email protected] on January 27, 2009, 04:15:48 AM

You probably have the Extras->RPM Limiters set, also make sure that the ALS is off, and that the Launch control value Fuel based Launchcontrol RPM limit is set correctly.

Title: Re: Rev limiter doesn't work (???)
Post by: [email protected] on January 27, 2009, 04:27:04 AM

Oh, yeah, try using a newer firmware http://www.vems.hu/wiki/index.php?page=MegaTune
Something like VemsMT1.0.78rc2 should be good - mind that you read the release notes.

Title: Re: Rev limiter doesn't work (???)
Post by: jadzwin on January 28, 2009, 03:52:28 AM

I've upgraded the firmware but it doesn't help :( (hewever the firmware is very interresting, especcialy 3d boost map and N20 support).

The only change in engine behaviour is that the soft limiter starts to work below 6500 (in firmware 1.0.73 it doesn't work at all) but limiter from basic settings doesn't work :(

I saw a status information in log. Is there any description of bits of this status data ? I can see on log that the VEMS status is changing around 6500.

This vems is not lucky. It was delivered to me with broken P259 and bridges across the AVR pins :( And now there is a problem with RPM limit.
I have never had such issue, but I suppose that I've made some silly bug in configuration. Maybe the problem is that the car is 5 cylinder with cam sync ?

Thank you for help
Kua

Title: Re: Rev limiter doesn't work (???)
Post by: MWfire on January 28, 2009, 04:05:26 AM

Did you turn ALS?

Title: Re: Rev limiter doesn't work (???)
Post by: jadzwin on January 28, 2009, 04:34:19 AM

Seems that ALS is turned off...

I've checked the config once again and I found sth suspicious:

(http://www.ecumaster.com/lanos/fc/als.jpg)

Title: Re: Rev limiter doesn't work (???)
Post by: MWfire on January 28, 2009, 04:53:00 AM

Check megatune,extras,advanced ALS, input channel use. This must be disabled

Title: Re: Rev limiter doesn't work (???)
Post by: [email protected] on January 28, 2009, 02:39:54 PM

As I said:

Quote from: [email protected] on January 27, 2009, 04:15:48 AM
.... and that the Launch control value Fuel based Launchcontrol RPM limit is set correctly.

Set it to either the point that you want the fuel cut - or 25500 to turn it off.

Title: Re: Rev limiter doesn't work (???)
Post by: jadzwin on January 29, 2009, 03:10:57 AM

The problem was connected to Launch controll as you wrote (I didn't read it precisely :()

Thank You for help!
Jadzwin

Title: Re: Rev limiter doesn't work (???)
Post by: [email protected] on January 29, 2009, 05:10:03 AM

No problem, enjoy those high revs ;D

VEMS Community Forum

Technical => Fuel Injection => Topic started by: jadzwin on January 27, 2009, 03:50:48 AM