Author Topic: Running 2 knock sensors on my v8  (Read 6684 times)

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Running 2 knock sensors on my v8
« on: July 04, 2009, 04:11:26 pm »
Hi Guys,
been a while since i been on i know but due to job problems etc the car has been laid up engine less for a year nearly,
But the new engine is being fitted in the next couple of weekes and want to sort the vems loom out while the engine bay is empty,
Im going to be running wasted spark ignition this time round and wondered how i go about connecting up a pair of knock sensors?
do they need splicing together? or do they go to seperate pins on the vems?

thanks for the help in the past.

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
Re: Running 2 knock sensors on my v8
« Reply #1 on: July 04, 2009, 06:16:53 pm »
They go to separate signal pins but have a common ground.

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Re: Running 2 knock sensors on my v8
« Reply #2 on: July 05, 2009, 12:27:13 am »
is there a pin out for dual knocks Dave?
as i think mine only shows a single knock sensor wiring.

thanks,

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74

Offline gunni

  • Hero Member
  • *****
  • Posts: 1492
  • BHP: 37
Re: Running 2 knock sensors on my v8
« Reply #3 on: July 05, 2009, 02:49:32 am »
http://195.159.109.134/vemsuk/forum/index.php/topic,99.0.html

It´s on the very first page you posted this thread into ;)

Offline Sprocket

  • Hero Member
  • *****
  • Posts: 867
  • BHP: 29
Re: Running 2 knock sensors on my v8
« Reply #4 on: July 05, 2009, 03:57:59 am »
I would check that all the components are on the board for the second knock channel ;) Check the shcematics and compare with your board

Offline Tony C

  • Hero Member
  • *****
  • Posts: 650
  • BHP: 8
    • Capriracing
Re: Running 2 knock sensors on my v8
« Reply #5 on: July 05, 2009, 03:27:09 pm »
cheers guys

so if i have this right,
one wire from K1 and K2 both join into pin2 of EC18
the other wire from K1 goes to pin1 of EC18
the other wire from K2 goes to pin3 of EC18

and the outer shielding wire of both K1 and K2 wires go to the main sensor earth point of EC36

that look right?
« Last Edit: July 05, 2009, 03:36:04 pm by Tony C »

Vems Ecu, Twin Plenum efi and N2o
13.314 @ 104.39 mph (10/06/07 3.9 v8)
Sponsored by: www.caprisport.com & www.interpart.biz
Web site: http://www.capriracing.co.uk

Vems Firmware: V1.1.74