Author Topic: 1.1.44 alpha released  (Read 152755 times)

Offline Sambas

  • Sandwiches
  • Jr. Member
  • *
  • Posts: 71
  • BHP: 15
1.1.44 alpha released
« on: November 24, 2008, 08:03:28 pm »
Available here:
http://kotisivu.dnainternet.net/sakrkorh/vems/firmware_1.1.44alpha2.zip

since 1.1.44:
  • Customlcd is on page 4
  • Customlcd cleaner design
  • SIPR protocol bugfix (always return with ign_table )
  • Config switch also swaps configs, megatune shows used slot flag. Both configs need to be prepared for correct slot and correct slot has to be manually selected when uploading. For example slot0 confswitch=199 and slot1 confswitch=215
  • requested tenpoint cranking pulsewidth curve, used if config.cwl=config.cwh=0
« Last Edit: November 25, 2008, 08:21:36 am by Sambas »
Firmware, Software and Hardware

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: 1.1.44 alpha released
« Reply #1 on: November 24, 2008, 08:37:28 pm »
:)
Just load it onto my test board!

Are "geek" LCD is dropped? I suggest leave it. Page 4 and 8 is unusable. May be it is possible replace one with old mode?

In new LCD i miss EgoC. It looks more valuable info than advance.
EgoC can tell much if some problem is rising. But advance is only a result. similar to PW on "geek" style.

My strategy is sell LCD for every customer. Main reason - with LCD is easy to solve simple problems by phone. No need for laptop and me.

Gints

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: 1.1.44 alpha released
« Reply #2 on: November 24, 2008, 08:43:58 pm »
    • requested tenpoint cranking pulsewidth curve, used if config.cwl=config.cwh=0
    Sorry. What it means?

    Offline GintsK

    • Hero Member
    • *****
    • Posts: 1257
    • BHP: 50
    Re: 1.1.44 alpha released
    « Reply #3 on: November 24, 2008, 09:24:24 pm »
      • requested tenpoint cranking pulsewidth curve, used if config.cwl=config.cwh=0
      Sorry. What it means?

      In mortal language: if both - CrankWarmPW and CrankColdPW is 0ms, cranking table being used. Right? :)[/list]

      Offline GintsK

      • Hero Member
      • *****
      • Posts: 1257
      • BHP: 50
      Re: 1.1.44 alpha released
      « Reply #4 on: November 24, 2008, 09:50:51 pm »
      Megatune now is much clearer! Graphical editing rules! Now i see how lumpy was my IAC curve  ;D

      What is Boostswitch?

      I have switching configs on my test board.  :D

      Offline Sambas

      • Sandwiches
      • Jr. Member
      • *
      • Posts: 71
      • BHP: 15
      Re: 1.1.44 alpha released
      « Reply #5 on: November 25, 2008, 07:47:55 am »

        Are "geek" LCD is dropped? I suggest leave it. Page 4 and 8 is unusable. May be it is possible replace one with old mode?

        In new LCD i miss EgoC. It looks more valuable info than advance.
        EgoC can tell much if some problem is rising. But advance is only a result. similar to PW on "geek" style.


        geekmode is not dropped, it just got replased this customlcd. I think I'll put this customlcd to page 4.

        In mortal language: if both - CrankWarmPW and CrankColdPW is 0ms, cranking table being used. Right? :)[/list]

        Yes.

        What is Boostswitch?

        It can scale your BoostDCtable on fly, either by potentiometer or switch and voltagedivider.
        Firmware, Software and Hardware

        Offline Sambas

        • Sandwiches
        • Jr. Member
        • *
        • Posts: 71
        • BHP: 15
        Re: 1.1.44 alpha released
        « Reply #6 on: November 25, 2008, 08:22:46 am »
        Release version is now alpha2
        Firmware, Software and Hardware

        Offline Arvid

        • Jr. Member
        • **
        • Posts: 26
        • BHP: 2
        Re: 1.1.44 alpha released
        « Reply #7 on: November 25, 2008, 12:06:06 pm »
        Hi!

         Can I use the 1.1.44 with simple trigger? 2 teeth hall trigger, plus hall trigger camsynk? ::)

        Offline Sambas

        • Sandwiches
        • Jr. Member
        • *
        • Posts: 71
        • BHP: 15
        Re: 1.1.44 alpha released
        « Reply #8 on: November 25, 2008, 01:01:11 pm »
        Hi!

         Can I use the 1.1.44 with simple trigger? 2 teeth hall trigger, plus hall trigger camsynk? ::)

        Did quick test and it should be ok. c004 signal-> coiltype, No. teeth=4, triggertooth=0, another triggertooth=1, toothwheel width=180, secondary trigger=25 and reftooth table=[0,3,2,1]
        Firmware, Software and Hardware

        Offline rob@vems.co.uk

        • Hero Member
        • *****
        • Posts: 3115
        • BHP: 49
          • VEMS Forum
        Re: 1.1.44 alpha released
        « Reply #9 on: November 25, 2008, 02:04:29 pm »
        I've done some work on the .ini file, really mainly polishing work, cleaning up titles and so on.
        The cold cranking is only adjustable if the two cranking values are set to zero.
        Save a copy of: http://www.vems.co.uk/VEMSDev/vemsv3_1.1.44.ini
        And rename it to vemsv3.ini then put it in any of the profiles you want.

         

        Offline Sambas

        • Sandwiches
        • Jr. Member
        • *
        • Posts: 71
        • BHP: 15
        Re: 1.1.44 alpha released
        « Reply #10 on: November 25, 2008, 04:00:37 pm »
        I've done some work on the .ini file, really mainly polishing work, cleaning up titles and so on.
        The cold cranking is only adjustable if the two cranking values are set to zero.
        Save a copy of: http://www.vems.co.uk/VEMSDev/vemsv3_1.1.44.ini
        And rename it to vemsv3.ini then put it in any of the profiles you want.

         

        Updated the packet with your file including some additions. If someone wants to contribute, we could use some helppages (the ones that appear when F1 is pressed) for the megatune menus. Just simple guide what does the variables mean in current menu with examples, default values etc.
        Firmware, Software and Hardware

        Offline MWfire

        • Hero Member
        • *****
        • Posts: 721
        • BHP: 35
        Re: 1.1.44 alpha released
        « Reply #11 on: November 27, 2008, 02:37:06 pm »
        Today tried config/tables switch and works perfekt. Now i can use pwm for lpg(0.9ohm injectors) and no pwm for gasolin(15ohm injectors).
        Tnx for this update.

        Offline gunni

        • Hero Member
        • *****
        • Posts: 1492
        • BHP: 37
        Re: 1.1.44 alpha released
        « Reply #12 on: November 30, 2008, 12:23:14 pm »
        In the .ini file ,
        fuel pressure gauge is analog channel 7 input, would it not just be simple to call it that?

        Offline Arvid

        • Jr. Member
        • **
        • Posts: 26
        • BHP: 2
        Re: 1.1.44 alpha released
        « Reply #13 on: November 30, 2008, 01:29:45 pm »
        Hi!

         Can I use the 1.1.44 with simple trigger? 2 teeth hall trigger, plus hall trigger camsynk? ::)

        Did quick test and it should be ok. c004 signal-> coiltype, No. teeth=4, triggertooth=0, another triggertooth=1, toothwheel width=180, secondary trigger=25 and reftooth table=[0,3,2,1]

        Hello, Thank you for your help! Tested Firmvare 1.1.44 today. The car started without any problems. :-)

        Offline gunni

        • Hero Member
        • *****
        • Posts: 1492
        • BHP: 37
        Re: 1.1.44 alpha released
        « Reply #14 on: November 30, 2008, 03:34:43 pm »
        Any more info on setting up the dual config?