Author Topic: Version 1.1.16 ***EXPERIMENTAL***  (Read 12332 times)

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Version 1.1.16 ***EXPERIMENTAL***
« on: March 04, 2007, 06:30:50 pm »
An experimental version of the VEMS firmware and MegaTune software is available here.
It provides new triggering algorithms, changes in ALS, Launch control, IAT retard, simplified boost control, misfire detection.
Be careful of the new ignition output schema.

http://www.vems.co.uk/VEMSTech/VemsMT1.1.16.zip

Offline jassem99

  • New Users
  • *
  • Posts: 1
  • BHP: 0
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #1 on: March 17, 2007, 12:26:14 am »
Rob, the wiki keeps talking about the new ignition output schema, but I can't figure it out. Yes the ignition output table is not correct when I migrated, but even when I corrected the table using terminal it was still no go for the new firmware. Reference tooth table h[1]= 1E 00 1E 00 since it's a 4 cylinder 60-2 wastespark. I spent all afternoon on this issue and it was to no avail. Can it be that hard to set it right?!

Basil

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #2 on: March 17, 2007, 05:36:14 pm »
I've got it running on a 24 tooth + 1 sync cam sensor.
But remember that 1.1.xx is experimental code, the suggested release is 1.0.69:

http://www.vems.co.uk/VEMSTech/VemsMT1.0.69.zip

Best to use this unless you have some unusual trigger requiements

Rob

Offline sm

  • Jr. Member
  • **
  • Posts: 46
  • BHP: 1
  • Time Attack 2007
    • Nissan 200SX Owners Club
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #3 on: March 17, 2007, 11:51:03 pm »
I've got it running on a 24 tooth + 1 sync cam sensor.
Guess thats my car then?
VEMS Powered Time Attack Car
350+ bhp Nissan 200SX S13 - Apex Performance K-Sport, AP-Tuning, DickinsonCMS.
www.sxoc.com

Offline damo_S13

  • Full Member
  • ***
  • Posts: 140
  • BHP: 5
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #4 on: March 19, 2007, 12:59:19 am »
yeah must be your kev... got mine reading the 24 + 1 sys fine today. plus spark :)
building vems 4age with itb powered corolla

Offline Team_Dandism

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 1
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #5 on: March 21, 2007, 12:21:00 pm »
Has anyone done this update on a 4age engined car yet, how hard is it to get the crank triggering setup again?

regards

Matt J..

www.team-dansism.co.uk

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #6 on: March 21, 2007, 07:10:44 pm »
Its not going to be massively problematic, I've just not done one yet so I can't give support on how to do it, yet.

If we can meet up at somepoint I can use your car as a test bed! ;)

Rob

Offline Team_Dandism

  • Jr. Member
  • **
  • Posts: 7
  • BHP: 1
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #7 on: March 21, 2007, 11:37:15 pm »
Ok cool i may just take you up on that. Think the tank has enough range to get me up to your place.

regards

Matt J..

www.team-dansism.co.uk

Offline irishtwincam

  • Full Member
  • ***
  • Posts: 199
  • BHP: 9
Re: Version 1.1.16 ***EXPERIMENTAL***
« Reply #8 on: March 22, 2007, 10:18:07 am »
Do it Do it Do it.