Author Topic: im lost  (Read 21250 times)

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
im lost
« on: April 09, 2008, 08:38:23 pm »
I must say that i´m totally lost, in setting up the Subaru trigger ,
I´m even lost in  getting the right H2 table, as i just can change it in the config( for some strange reasen)

I have uploaded 1.0.73 and that is working, but the H2 table is still the old setup from 1.0.38.

I can not run download config with the megatune in the 1.0.73 packede,
but i can do it with megatune from the 1.0.53 packede, but i cant copy that to the 1.0.73 packede, then they will just be empty.

Can someone help me , so i can get this working?.

The Trigger setting is even worse, and i also need some help for that.


/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #1 on: April 09, 2008, 09:40:26 pm »
You can't use MegaTune to do upgrades.

Use Download-config.bat to get your configuration and tables files.

Make your changes to the H2 table,

Generate config, then upload.  You'll probably have anti-lag issues upgrading from 1.0.38 so use generate config with defaults.

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #2 on: April 10, 2008, 07:33:45 am »
thanks , that was the plan,
But i can´t use download config,i just writes "unit not ready, unit not ready , unit not ready.

I can only use down load config, when i use the 1.0.53 packede, but then i cant copy that to the 1.0.73 ,so i can generate config.


working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #3 on: April 10, 2008, 08:04:08 am »
Do the files that 1.0.53 downloads contain anything or are they empty?
If you are getting "Unit not ready" then you have a problem greater than uploading a new configuration will solve.

Once you have the correct firmware uploaded you should be able to access the config and tables setup easily.

Rob

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #4 on: April 10, 2008, 09:44:40 am »
If i use the download from 1.0.53, then it´s fine, but i just cant upload them again,

it is 1.0.73 that is in the ECU,but for some strange reason i just cant use the download from that packede,
I just tryed to put in 1.1.xx firmware and that is also fine, can even use the download ,
but i also dont have anything that i need to take from the old firmware to the new firmware,
So does it matter?

/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #5 on: April 10, 2008, 10:40:00 am »
I dont understand what's happening...

Using 1.0.53 you can download the config?
Then you copy the config and tables from the 1.0.53 configs folder to 1.0.73's configs folder, then run generate-config12x12WithDefaults.bat
but when you run upload-config.bat you get an error?

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #6 on: April 10, 2008, 10:48:02 am »
I dont understand what's happening...

Using 1.0.53 you can download the config?
----------------------------------------------------------------------------------------------------------
Yep, that is working fine.

Then you copy the config and tables from the 1.0.53 configs folder to 1.0.73's configs folder,
----------------------------------------------------------------------------------------------------------
Allready here, there is a problem,as all the text, when moved, is written vertikal, and not lateral,
So the generate config does not work.
----------------------------------------------------------------------------------------------------------

 then run generate-config12x12WithDefaults.bat
but when you run upload-config.bat you get an error?
« Last Edit: April 10, 2008, 11:52:21 am by Denmark »
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #7 on: April 10, 2008, 11:00:39 am »
?

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #8 on: April 10, 2008, 11:52:59 am »
Just ignore the blue field, i have written in between :)
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #9 on: April 10, 2008, 11:59:55 am »
Can you post a section of the download here?

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #10 on: April 10, 2008, 01:03:40 pm »
I can only figure out, how to make a screen dump.





this is downloaded from the packede 1.0.53


/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #11 on: April 10, 2008, 02:45:17 pm »
I cant see much wrong with that...
What errors are given when you run generate-config12x12.bat?

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: im lost
« Reply #12 on: April 10, 2008, 03:56:29 pm »
It´s writing in danish,
Not ready ,not ready, some 30times or so, then it comes to the tables, and do the same,

But if it looks allright, it dosent matter, if i need to show the config, i can just download it with eigher the older or newer version, the only one i cant do it with, is 1.0.73.

I have even tryed to delete the one i hadinstalled, and downloaded it from a difference source.

Still the same.


Thanks,
Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: im lost
« Reply #13 on: April 10, 2008, 09:11:36 pm »
Is it writing not ready when you upload or download?

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
Re: im lost
« Reply #14 on: April 11, 2008, 12:22:15 am »
Silly question, but is the script set to use the right comm port? 

I've been caught by this one once...