Author Topic: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor  (Read 17533 times)

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #15 on: March 25, 2008, 10:51:47 am »
I've never run out of grounds on any of the adaptors that I've made, but there arent too many spare ;)
The 5 that come from the VEMS are joined together (ground cluster) 12cm from the EC36 plug, then I usually take the ground on the chassis plug that is specifically a sensor ground, add that to the ground cluster, then use that wire to give the serial plug on EC18 a ground.
Then you'll need one to connect the sheild for the wires to the VR inputs.

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #16 on: April 04, 2008, 05:02:49 pm »
I´m also on my way now



It´s setup for 2 Vr sensors, EC18 pin12(secondery) that is showed as EC36 pin13 in the Phatbob  manual!!

I just run out off the crimping, but will add it when i get some,
this is the complete wiring,
just IAT and wideband missing, so it´s,
boostcontrol,aircon cut relay,fans, iac, knocksensor,mapsensor.

The ignition is setup as, the first 4 ch are logic,and the 4last are with fets, inj fet 1234 are injector 1-2-3-4, injfet 7&8 are iac close& iac open
aircon cut relay p259 ch0, to cut aircon when going wot.
fan control p259 ch1.

then i just need to be able to configure a tacho output to the cluster.
/Skassa
« Last Edit: April 04, 2008, 05:06:07 pm by Denmark »
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #17 on: April 04, 2008, 09:18:34 pm »
You dont seem to have the grounds joined...  Likely to kill the p259 without it.

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #18 on: April 04, 2008, 09:30:22 pm »
Okay,

I just didnt thinkit was nessery,
I have all the sensor, and shield on pin26,
and the rest on the last four grounds, that are internaly conneted, is it really nessesary to connect the externale?

/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #19 on: April 04, 2008, 10:09:13 pm »
Its VITAL thats why I drew:


Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #20 on: April 04, 2008, 10:11:44 pm »
Okay,

I will put a wire a cross the grounds, then :)


Thanks,
I did the last time acutully burn the p259 chip, so that could be why  ::)


/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #21 on: April 05, 2008, 12:49:42 am »
Its easily done

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #22 on: April 05, 2008, 08:11:21 am »
Yep.


Did you see that you in the manual writes that it´s EC36 pin13 that is for a VR sensor, but it´s EC18 pin 12.


No i just need the time to plug it in, to see if i can get at trigger signal..

/Skassa
working on the boxer

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #23 on: April 09, 2008, 08:03:28 am »
Dnb,

Did you have any luck with getting the engine finished, and if.

Have you tryed ,if the trigger setup is working?


Now that i have put a wire across the ground wires,
I will today try to plug mine in, the problem is that i dont got a 12v supply,so i have to put it into the car, to test.
and i dont even know what firmware that comes with my board(number1484).



/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #24 on: April 09, 2008, 10:04:30 am »
It will probably be something around 1.0.3x to 1.0.5x
As for a 12v power supply... I use a spare drive power connector inside my PC the VEMS only draws a few milliamps so you can have fun testing it on the bench.

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #25 on: April 09, 2008, 10:23:54 am »
Thanks,

Do You still think that i need to put in the older firmware,like 1.0.73 ?



Smart move with the power, but i will now go and plug it in the car, and try the subaru setting that is written on Wiki,and see if i can get a cranking signal ::)



/Skassa
working on the boxer

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #26 on: April 10, 2008, 08:07:17 am »
1.0.73 is the firmware to use, its running hundreds of engines for over a year now.

I think you need to start afresh with the config and tables for this install.

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #27 on: April 11, 2008, 12:20:49 am »
Sorry for my absence - no further progress on the VEMS side of my Scoob project.  I got caught up quite badly in "real" work

Offline Denmark

  • Hero Member
  • *****
  • Posts: 542
  • BHP: 7
Re: Finally finished the prototype MY93 to 96 Subaru plug and play adaptor
« Reply #28 on: April 11, 2008, 08:03:58 am »
Okay, i know how it feels, i would be a lot nicer, if the same money con into the account, and didn´t have to work for it,
then there would be better time, to project like this  :)

Maybe you could  review the trigger, injector and ignition settings, to check if it looks right?



/Skassa
working on the boxer