« previous next »
Pages: [1]

Author Topic: LCD keeps switching into map editing mode  (Read 11803 times)

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
LCD keeps switching into map editing mode
« on: September 05, 2007, 12:50:29 pm »
My LCD keeps switching for no good reason into the map editing mode from the usual parameter display mode.

I can see no reason for this, since I don't have a keyboard connected at the moment.

Anyone care to guess why?
Logged

Offline cliffb75

  • Global Moderator
  • Full Member
  • *****
  • Posts: 167
  • BHP: 10
Re: LCD keeps switching into map editing mode
« Reply #1 on: September 05, 2007, 09:08:42 pm »
Its because electronics are the work of satan.......


Sorry, I mean, I have no idea  :)
Logged

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
Re: LCD keeps switching into map editing mode
« Reply #2 on: September 05, 2007, 11:55:45 pm »
And TVR electronics are made by his evil twin brother... ;)
Logged

Offline Agriv8

  • Full Member
  • ***
  • Posts: 145
  • BHP: 4
Re: LCD keeps switching into map editing mode
« Reply #3 on: September 06, 2007, 09:23:40 pm »
always thought Lucifer is very similar to lucas ( more than a little similar in name dont you think !!! )

certainly my dealing with my lucas hotwire system backs this up !!! but it makes yo apreciate the vems a lot more

regards

Agriv8
Logged
'The older I get the faster I was'

Offline Timmo6

  • Jr. Member
  • **
  • Posts: 43
  • BHP: 3
Re: LCD keeps switching into map editing mode
« Reply #4 on: February 06, 2008, 05:50:23 pm »
Quote from: dnb on September 05, 2007, 12:50:29 pm
My LCD keeps switching for no good reason into the map editing mode from the usual parameter display mode.

I can see no reason for this, since I don't have a keyboard connected at the moment.

Anyone care to guess why?
Yeah I had this too. Must be a wiring issue I guess. Some short may happen I think.
Logged

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: LCD keeps switching into map editing mode
« Reply #5 on: February 06, 2008, 10:05:04 pm »
It must be a noise problem. I have two cars with this. One, running peak-hold injectors, even show total garbage sometimes. For a some reason LCD is very sensitive.

May be we can found solution to protect LCD.
Logged

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: LCD keeps switching into map editing mode
« Reply #6 on: February 06, 2008, 10:27:43 pm »
Its noise, these LCDs sit outside of the ECU, if the connections are unproperly shielded or grounded, the noise will cause issues with that peice of the circuit.
Logged

Offline dnb

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 837
  • BHP: 19
Re: LCD keeps switching into map editing mode
« Reply #7 on: February 06, 2008, 10:56:51 pm »
I don't have the "total garbage" problem any more, but sometimes it still enters map editing mode.
This cannot be noise on the LCD because it's displaying whatever it is told.

All it can be is noise picked up by not having a keyboard plugged in, so I intend to make something to plug in to the PS2 connector to ground the data line.  This should stop the problem.
Logged
Pages: [1]
« previous next »