Drive by wire controller

[Denmark]

Hi all

Have Any of you used or know of a dbw controller that could be used together with vems ?


Thanks
Skassa

[gunni]

I would never work with a DBW controller that is standalone and takes orders over CAN or anything similar, you simply never know what could happen and how the controller would react when there are issues in signaling and such.

[MWfire]

I made my version for one car
http://www.youtube.com/watch?v=p5H91pLEzVE
also one more solution
http://www.youtube.com/watch?v=o1Y_MwPhHfE

[Denmark]

i could really use this, so i could change the ecu in some of the newer subaru´s , Impreza STI + Forester, but also so i can use a dbw complete manifold,

There is one made for the subaru´s in Aus, but its 450$, but that is a complete standalone with mapping software, and for the vems , i could use the tps output from the pedal sensor, this have built in safety,
but its still recommended for none moving engines
I assume that is "if anything happens" , that there is that recommended text

MWfire, is it for a costumers car you have made that controller?



Thanks,
Skassa

[MWfire]

So far it works great, but i didn't finished all things(i was working on cdi, mapping lot of cars). So yet is only for me.

[Kamuto]

I have used pololu jrk controler for throttle control few times, but it has not any settings for idle, so idle valve needed aditionaly

[Kamuto]

btw it would be great if vems could have 0-5v output, maybe there is any chip who can be used instead of one wire interface? it could work with pololu.

[Denmark]

Looks like vems is almost ready for dbw ,
Anyone know what input and outputs the Can be used on the pcb ?

I''m ready to test on Subaru's

[Kamuto]

ok, now we have drive by wire, that's good, controlled from 6-7 injector channel, that's bad if you want to start v8 engine with that. so, is there any possibility with newer firmwares to use any other output for that? thanks. I'm starting mercedes amg v8 soon, so I'm intrested how to use injector channels, make it 2 injectors on channel or wait some time

[MWfire]

ok, now we have drive by wire, that's good, controlled from 6-7 injector channel, that's bad if you want to start v8 engine with that. so, is there any possibility with newer firmwares to use any other output for that? thanks. I'm starting mercedes amg v8 soon, so I'm intrested how to use injector channels, make it 2 injectors on channel or wait some time

Yes, you can use pwm for injectors. So no problem for v8.

[Kamuto]

ok, now we have drive by wire, that's good, controlled from 6-7 injector channel, that's bad if you want to start v8 engine with that. so, is there any possibility with newer firmwares to use any other output for that? thanks. I'm starting mercedes amg v8 soon, so I'm intrested how to use injector channels, make it 2 injectors on channel or wait some time

Yes, you can use pwm for injectors. So no problem for v8.

but if  we try to make it sequential, then it's not enough outputs

[MWfire]

ok, now we have drive by wire, that's good, controlled from 6-7 injector channel, that's bad if you want to start v8 engine with that. so, is there any possibility with newer firmwares to use any other output for that? thanks. I'm starting mercedes amg v8 soon, so I'm intrested how to use injector channels, make it 2 injectors on channel or wait some time

Yes, you can use pwm for injectors. So no problem for v8.

but if  we try to make it sequential, then it's not enough outputs

You have 8 injectors drivers + injector pwm driver. So, yes you can make v8 sequential and have DBW.

[Kamuto]

ok, now we have drive by wire, that's good, controlled from 6-7 injector channel, that's bad if you want to start v8 engine with that. so, is there any possibility with newer firmwares to use any other output for that? thanks. I'm starting mercedes amg v8 soon, so I'm intrested how to use injector channels, make it 2 injectors on channel or wait some time

Yes, you can use pwm for injectors. So no problem for v8.

but if  we try to make it sequential, then it's not enough outputs

You have 8 injectors drivers + injector pwm driver. So, yes you can make v8 sequential and have DBW.

ok, how? last time I have got assembled  vems with dbw in box it used 6-7 injector channels. one channel cut before the injector driver chip. so how it must be connected? it would be nice to get more detailed instructions

[Kamuto]

someone?

[MWfire]

yellow area is pwn output.

I can add you H bridge for DBW using that output. From where are you?