« previous next »
Pages: [1]

Author Topic: 1.1.95 - No menu options for wheelspeed  (Read 8260 times)

Offline Pet

  • Full Member
  • ***
  • Posts: 121
  • BHP: 7
1.1.95 - No menu options for wheelspeed
« on: October 11, 2011, 10:03:51 am »
As I can see here on WikI http://www.vems.hu/wiki/index.php?page=IssueReports :
Quote
1.1.95 - No menu options for wheelspeed running latest nightly VT 7-12. Checked Firmware Parameters and it lists a 1 for PS2. I then downloaded both 'wheelspeed' & 'ps2' firmware to vems and neither of them showed a 0 for ps2.

 It means there is no chance to show menu in VT and use WheelSpeed input with that FW ???? Thanks.
Logged

Offline jrussell

  • VEMS USA
  • Administrator
  • Full Member
  • *****
  • Posts: 224
  • BHP: 15
    • VEMS USA
Re: 1.1.95 - No menu options for wheelspeed
« Reply #1 on: October 11, 2011, 12:35:21 pm »
If you are using the 2011-07-12 version of VemsTune, it's strongly encouraged to update to the newest released which is 2011-09-07.

http://www.vems.hu/vt/
Logged
VEMS USA - Located in beautiful Burlington, Vermont
1988 RX7 Turbo

Offline Pet

  • Full Member
  • ***
  • Posts: 121
  • BHP: 7
Re: 1.1.95 - No menu options for wheelspeed
« Reply #2 on: October 11, 2011, 01:20:02 pm »
No, I am using the latest nightly VT, only not sure yet, if I have PS2 or WheelSpeed FW version......in any case, I don't have Speed menu now...
Logged

Offline jrussell

  • VEMS USA
  • Administrator
  • Full Member
  • *****
  • Posts: 224
  • BHP: 15
    • VEMS USA
Re: 1.1.95 - No menu options for wheelspeed
« Reply #3 on: October 11, 2011, 01:41:29 pm »
It's not under Base Setup -> Speed Sensor?

Logged
VEMS USA - Located in beautiful Burlington, Vermont
1988 RX7 Turbo

Offline Pet

  • Full Member
  • ***
  • Posts: 121
  • BHP: 7
Re: 1.1.95 - No menu options for wheelspeed
« Reply #4 on: October 11, 2011, 01:59:54 pm »
No, it isn't there.
Logged

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: 1.1.95 - No menu options for wheelspeed
« Reply #5 on: October 11, 2011, 09:37:48 pm »
uploaded wrong firmware with ps/2 support ?
Logged

Offline Pet

  • Full Member
  • ***
  • Posts: 121
  • BHP: 7
Re: 1.1.95 - No menu options for wheelspeed
« Reply #6 on: October 12, 2011, 06:17:53 am »
Yes maybe, I'll check it once more today....

Edit: my fault, PS2 version was there, re-uploaded with wheel-speed version and Speed menu is visible already. Thanks.
« Last Edit: October 12, 2011, 08:25:19 pm by Pet »
Logged

Offline Pet

  • Full Member
  • ***
  • Posts: 121
  • BHP: 7
Re: 1.1.95 - No menu options for wheelspeed (solved) + another problem
« Reply #7 on: November 01, 2011, 08:13:40 am »
Hi, I tried speed input (ABS signal through LM1815 circuit) and I can see some strange behaviour: car was on my garage and both wheels were lifted (only for test); when there was some roadspeed (tps was already 0), idle rpm was around 1600 (normal idle is around 1050), ign wasn't changing (i have ign regulation for idle enabled) and idle DC was also too high - it seems there was idle regulation disabled when roadspeed was > 0 (see the graph). If speed was falling down to zero, then normal idle regulation (idle dc + ign) was enabled again after aprox. 1s. Any ideas ?? Thanks.

Logged

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: 1.1.95 - No menu options for wheelspeed
« Reply #8 on: November 01, 2011, 09:17:01 pm »
Not whole IAC disabled, but just Integral particle. You can enable it under Idle settings. If you tune IAC so that I part is always negative at target rpm it gives nice rpm settle down when car stops. Just like OEM.

Gints
Logged
Pages: [1]
« previous next »