« previous next »
Pages: [1]

Author Topic: 1.1.90 fw IAC on / timing retarding during pulls  (Read 9491 times)

Offline lugnuts

  • Full Member
  • ***
  • Posts: 249
  • BHP: 2
1.1.90 fw IAC on / timing retarding during pulls
« on: April 29, 2011, 01:40:53 am »
Logged

Offline tweak

  • Jr. Member
  • **
  • Posts: 58
  • BHP: 3
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #1 on: May 13, 2011, 11:21:52 pm »
Occasionaly seeing the same after upgrade to 1.1.88
IAC goes on with ignition jumping up and down 10-20°, specially felt at low rpm and causing "kangarooing" when i release the clutch.

Now i'm also getting suspicious if its going on during cruising, causing higher EGT and increased consumption than before upgrade.

Need to get back to this more i think...
Logged

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #2 on: May 17, 2011, 09:03:52 am »
 >:(  I got something similar on 1.1.88 ! Engine runs good during two weeks. And suddenly after hot restart IAC flag was ON always (except may be overrun). I downloaded config to PC, comparing it with previous - and it was exactly the same - no single sign difference!

Also I had bad luck with 1.1.88 on Subaru with stepper. IAC flag was so unpredictable - I was forced to downgrade to 1.1.85 or 81...

Gints
Logged

Offline lugnuts

  • Full Member
  • ***
  • Posts: 249
  • BHP: 2
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #3 on: May 17, 2011, 04:34:50 pm »
I've been OK on the 1.1.88, if it did it on the race cars I'd notice. Strange.
Logged

Offline boostd audi

  • Full Member
  • ***
  • Posts: 207
  • BHP: 9
    • vems.live
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #4 on: May 18, 2011, 07:36:15 am »
i had similar issue when i went to 1.1.90 and then i went back to 1.1.88
Logged
boost addict's Vems powered Audi VRT s2

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #5 on: May 20, 2011, 10:45:25 am »
I have log from 1.1.88 case if someone interested.
Logged

Offline lugnuts

  • Full Member
  • ***
  • Posts: 249
  • BHP: 2
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #6 on: May 20, 2011, 03:12:08 pm »
Quote from: GintsK on May 20, 2011, 10:45:25 am
I have log from 1.1.88 case if someone interested.

You could post it on my wiki page. 

They replied yesterday saying it is fixed in 1.1.92
Logged

Offline tweak

  • Jr. Member
  • **
  • Posts: 58
  • BHP: 3
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #7 on: June 02, 2011, 10:07:27 pm »
Any luck with 1.1.92?  Problem has been gone for a while here, but seemed to be back today.
I hope that upgrading does not lead to other issues then..

Btw. i put VEMS stickers on the car today, so  it can't be all that bad  ;)
Logged

Offline mattias

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1075
  • BHP: 41
    • Sävar Turbo Site
Re: 1.1.90 fw IAC on / timing retarding during pulls
« Reply #8 on: June 03, 2011, 10:15:35 am »
Quote from: tweak on June 02, 2011, 10:07:27 pm
Any luck with 1.1.92?  Problem has been gone for a while here, but seemed to be back today.
I hope that upgrading does not lead to other issues then..

Btw. i put VEMS stickers on the car today, so  it can't be all that bad  ;)
If you  read the wiki page linked in the first page, you'll see that setting "IAC close min map" to highest possible value negates any effect even if you continue to run the older firmware.
Logged
Pages: [1]
« previous next »