« previous next »
Pages: [1]

Author Topic: For Sale VEMS V3.2 $500 US OBO  (Read 7423 times)

Offline bcool

  • Full Member
  • ***
  • Posts: 149
  • BHP: 0
For Sale VEMS V3.2 $500 US OBO
« on: March 01, 2011, 01:18:28 am »
V3.2 VEMS
Bench tested by jrussell only used it once after that.
I just dont think this ECU will work for my application i've already purchased a Microtech out of frustration. The only thing to note is that the lead for one of the injectors on the board acted as a fuse during testing one day and thus the reason for the jumper to the pin. Comes with everything in picture. I will cut off the connector on the old harness but honestly it would be easier just to buy new econoseal connectors for your application rather than trying to de-pin the old one (It's a pain in the ass).

Comes with everything you see
V3.2 VEMS
LCD Display
Documentation
Serial cable

Album:
http://bcool.imgur.com/vems#DZOjo

« Last Edit: March 01, 2011, 05:27:14 am by bcool »
Logged

Offline bcool

  • Full Member
  • ***
  • Posts: 149
  • BHP: 0
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #1 on: March 10, 2011, 05:46:34 am »
$420 shipped in the US
Logged

Offline mattias

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1075
  • BHP: 41
    • Sävar Turbo Site
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #2 on: March 10, 2011, 11:30:02 am »
Tip: With a piece of 1 mm MIG welding wire pressed flat on end, or a miniature flat screw driver you can de-pin the Econoseal connectors in a couple of minutes, it's that easy.
Logged

Offline bcool

  • Full Member
  • ***
  • Posts: 149
  • BHP: 0
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #3 on: March 10, 2011, 04:42:52 pm »
True I may have already tossed the connector though. Come to find out why this wasnt working well for my setup was that I think i had the dwell too high with the MSD box and i destroyed a coil or 2. It would still run fine at low RPMs but would break up at higher RPMs; i would keep the unit if i had another useful project for it. haha
Logged

Offline DMS

  • Jr. Member
  • **
  • Posts: 26
  • BHP: 0
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #4 on: March 10, 2011, 05:19:44 pm »
Specs on the box itself?
Logged

Offline bcool

  • Full Member
  • ***
  • Posts: 149
  • BHP: 0
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #5 on: March 12, 2011, 05:01:59 pm »
3 IGBTs
6 Injector FET's
1 wideband fet
250k map
Logged

Offline BimmerDread

  • Jr. Member
  • **
  • Posts: 17
  • BHP: 2
Re: For Sale VEMS V3.2 $500 US OBO
« Reply #6 on: April 02, 2011, 08:02:36 pm »
Quote from: bcool on March 12, 2011, 05:01:59 pm
3 IGBTs
6 Injector FET's
1 wideband fet
250k map
Hi B, I am interested.
What car were you running it on?
Logged
Pages: [1]
« previous next »