« previous next »
Pages: 1 2 [3]

Author Topic: TPS weigh for ref DC  (Read 22894 times)

Offline AVP

  • Hero Member
  • *****
  • Posts: 743
  • BHP: 11
Re: TPS weigh for ref DC
« Reply #30 on: November 07, 2010, 10:09:29 pm »
audi has an external wastegate. With PID 0/0/0 it did not oscilate but from target of 300kpa, it only went to 230 and very very slowly.

I can also try reducing the solenoid Hz. According to turbosmart, it should be using around 10hz. If it goes too high it can oscilate. So i will give it a go tomorrow hopefully.

i have found that the dekas have 380 at 13V and 280 @ 14V

this value of 192 at which volt is it referring to? is it 14V or 13.2V?
Logged

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: TPS weigh for ref DC
« Reply #31 on: November 07, 2010, 10:15:54 pm »
look for table boost vs tps curve.
If tps weight is set to 0, no affect of tps.
Logged

Offline AVP

  • Hero Member
  • *****
  • Posts: 743
  • BHP: 11
Re: TPS weigh for ref DC
« Reply #32 on: November 07, 2010, 10:19:57 pm »
that is different than what Gints said further up.

so if you use 0 for that value, then TPS has no effect on boost? and if 100% then how much does TPS affect the boost ?
Logged

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: TPS weigh for ref DC
« Reply #33 on: November 07, 2010, 10:30:08 pm »
Quote from: AVP on November 07, 2010, 10:19:57 pm
that is different than what Gints said further up.

so if you use 0 for that value, then TPS has no effect on boost? and if 100% then how much does TPS affect the boost ?
for 100% is like is in tps table. If you put 200%, effect is double.
BTW effect is for boost ref DC and boost target.
Logged

Offline AVP

  • Hero Member
  • *****
  • Posts: 743
  • BHP: 11
Re: TPS weigh for ref DC
« Reply #34 on: November 07, 2010, 10:33:12 pm »
so to leave matters simpler, its best to leave it as 100% then?

it was and i have seen it being usually 398% for some reason.

does that quadruples the refDC and boost target? what is the point?
Logged

Offline MWfire

  • Hero Member
  • *****
  • Posts: 721
  • BHP: 35
Re: TPS weigh for ref DC
« Reply #35 on: November 07, 2010, 10:36:09 pm »
i use 20-40%. No surge problems, good spood...
Logged

Offline AVP

  • Hero Member
  • *****
  • Posts: 743
  • BHP: 11
Re: TPS weigh for ref DC
« Reply #36 on: November 07, 2010, 10:37:15 pm »
ok, thanks for that. Ill use 100% so that i know that my refDC and TPS are not influencing this anyhow.
Logged

Offline GintsK

  • Hero Member
  • *****
  • Posts: 1257
  • BHP: 50
Re: TPS weigh for ref DC
« Reply #37 on: November 08, 2010, 07:35:40 am »
Quote from: MWfire on November 07, 2010, 10:30:08 pm

for 100% is like is in tps table. If you put 200%, effect is double.
BTW effect is for boost ref DC and boost target.
MWfire, are you sure about boost target?
IMHO TPS vs  boost target - there is different 2D table. Mentioned value change just refDC. No?

AVP, 0% of this value means refDC directly from table with no changes from TPS position.
With 0/0/0 you have to found right refDC. Looks like it will be something like 80-90% for 290Kpa.
Logged

Offline AVP

  • Hero Member
  • *****
  • Posts: 743
  • BHP: 11
Re: TPS weigh for ref DC
« Reply #38 on: November 08, 2010, 09:01:25 pm »
today i noticed that if i use 0 or up to 40% on weigh to TPS the solenoid ticks. If i use 100 or above it is silent.

i guess if i use 0DC on 1000rpm that should also allow for the weigh to TPS to be 0% there.

by the way, with PID 0/0/0 boost target is reached but its much slower than what i had in megatune. as if i have much more lag.
i possibly need to introduce more DC sooner.

ill test it more!
Logged
Pages: 1 2 [3]
« previous next »