Author Topic: new to vems. failing at first hurdle  (Read 36383 times)

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
new to vems. failing at first hurdle
« on: October 25, 2009, 08:23:51 pm »
i have been running my car on a link ecu, but to cut a long story short it is borrowed. so i purchased a vems ecu.
and so far i just cant get the laptop, using serial on back not a usb converter, to talk to the vems box.

how do i know what version of software i need to talk to the vems.
how do i know what firmware is on vems if i cant talk to it.
and how do you upload new firmware??

thanks in advance
Hutchie

Offline gunni

  • Hero Member
  • *****
  • Posts: 1492
  • BHP: 37
Re: new to vems. failing at first hurdle
« Reply #1 on: October 25, 2009, 09:34:10 pm »

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #2 on: October 26, 2009, 08:06:35 am »
thanks but i have already read that, and printed it so i can follow it @ car, i simply cannot get the laptop to see the vems

Offline gunni

  • Hero Member
  • *****
  • Posts: 1492
  • BHP: 37
Re: new to vems. failing at first hurdle
« Reply #3 on: October 26, 2009, 04:32:24 pm »
Are you 100% sure you have.

12v and ground at the vems.
correct serial connection
correctly selected COM port?

Offline max

  • Jr. Member
  • **
  • Posts: 17
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #4 on: October 26, 2009, 04:44:30 pm »
Also try to set higher serial data rate. I couldnt get mine to work until I changed this to 19200. FW 1.1.53

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #5 on: October 26, 2009, 06:14:25 pm »
i have tried all the different speeds, but i have no idea what firm ware i have

definately have power and very good ground

:S

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: new to vems. failing at first hurdle
« Reply #6 on: October 26, 2009, 07:02:22 pm »
Where abouts are you?

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #7 on: October 27, 2009, 08:13:26 am »
im in the north east of england, i bought this vems off mini-valver (dave) you may know him




Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: new to vems. failing at first hurdle
« Reply #8 on: October 27, 2009, 05:36:38 pm »
That ECU should have firmware v1.0.73 on it.  You may have problems with newer versions trying to connect.
http://media.vems.se/code/VemsMT1.0.73Final.zip

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #9 on: October 27, 2009, 06:13:28 pm »
tried that  :'(

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: new to vems. failing at first hurdle
« Reply #10 on: October 27, 2009, 10:12:21 pm »
Have you tried swapping the tx and rx wires into the ec18 plug?

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #11 on: October 28, 2009, 01:34:51 am »
i thought it was plugged into that plug???


Offline paul_f

  • Full Member
  • ***
  • Posts: 120
  • BHP: 8
Re: new to vems. failing at first hurdle
« Reply #12 on: October 28, 2009, 03:27:02 am »
Did you make the harness?

Or are you plugging into the LCD connector?

Offline Hutchie

  • Jr. Member
  • **
  • Posts: 35
  • BHP: 1
Re: new to vems. failing at first hurdle
« Reply #13 on: October 28, 2009, 07:30:00 am »
the harness came with it

Offline rob@vems.co.uk

  • Hero Member
  • *****
  • Posts: 3115
  • BHP: 49
    • VEMS Forum
Re: new to vems. failing at first hurdle
« Reply #14 on: October 28, 2009, 03:19:16 pm »
Now that is really strange - the cable is a straight through pin 2 to pin 2 and pin 3 to pin 3 isnt it?