News:
When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Over-run fuel cut problem
Started by murjam |
2 Replies
4907 Views |
November 25, 2016, 07:34:59 amby murjam |
|
|
|
0 Replies
4907 Views |
May 10, 2012, 02:42:38 pm by fphil |
|
|
|
|
2 Replies
4935 Views |
July 12, 2010, 05:18:47 pm by wulfgang |
|
|
|
|
Tooth width
Started by AMGmercedes |
1 Replies
4978 Views |
May 14, 2010, 03:57:39 am by mattias |
|
|
|
0 Replies
5002 Views |
July 20, 2013, 07:37:56 pm by Mads Lund |
|
|
|
|
V3SDCard - no knock sensing?
Started by BigD |
2 Replies
5011 Views |
December 17, 2009, 08:04:59 pm by z0tya |
|
|
|
2 Replies
5039 Views |
September 01, 2014, 02:06:40 pm by fphil |
|
|
|
|
2 Replies
5068 Views |
March 21, 2013, 07:55:01 am by kasae86 |
|
|
|
|
reference tooth table
Started by Seight-v8 |
3 Replies
5075 Views |
November 26, 2009, 12:30:44 am by Seight-v8 |
|
|
|
1.8t 20v AGU Startmap/Config File.
Started by Mcprobie |
1 Replies
5095 Views |
March 11, 2019, 04:39:11 pm by MWfire |
|
|
|
rpm will not go up
Started by 306 2.0 16v |
1 Replies
5104 Views |
October 07, 2012, 09:50:33 pm by Erikk |
|
|
|
dv/dt value in VemsTune 'stuck'
Started by tweak |
2 Replies
5115 Views |
June 27, 2010, 08:08:09 pm by mattias |
|
|
|
Creating a custom gauge in Megatune
Started by gunni |
0 Replies
5121 Views |
April 28, 2009, 02:43:22 am by gunni |
|
|
|
coolant factor for 2050@25degc
Started by Seight-v8 |
3 Replies
5124 Views |
October 13, 2009, 08:56:52 am by dnb |
|
|
|
inverted - assign outputs
Started by Seight-v8 |
2 Replies
5181 Views |
April 30, 2010, 01:32:51 am by Seight-v8 |
|
|
|
ETC actuator is not moving
Started by Matus |
4 Replies
5199 Views |
July 10, 2016, 10:04:57 am by Matus |
|
|
|
1 Replies
5204 Views |
February 07, 2012, 09:16:40 am by Erikk |
|
|
|
|
Firmware Compatibility
Started by Tony C |
1 Replies
5219 Views |
January 11, 2010, 05:20:02 am by Sprocket |
|
|
|
Suitable MAP sensors for VEMS 3.3
Started by BimmerDread |
3 Replies
5244 Views |
February 26, 2010, 03:23:59 pm by GintsK |
|
|
|
Configuration for 36-1
Started by paul_f |
1 Replies
5248 Views |
January 21, 2009, 12:29:44 am by GintsK |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll