News:
When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
5 Replies
7358 Views |
October 13, 2009, 02:05:40 amby GintsK |
|
|
|
|
Sec trig position bad when revving off idle
Started by BigD |
5 Replies
7126 Views |
July 01, 2013, 05:20:48 pm by Joof |
|
|
|
Trigger errors
Started by SierraCos2wd |
5 Replies
6607 Views |
August 11, 2009, 06:59:47 am by d00ze |
|
|
|
AlphaN with MAP compensation
Started by ryniobl |
5 Replies
6250 Views |
March 14, 2014, 09:03:19 am by VEMS |
|
|
|
2nd RS232 for AIM
Started by fphil |
5 Replies
6379 Views |
March 18, 2014, 04:35:57 pm by VEMS |
|
|
|
Factory WBO2 Configurations
Started by Sanjuro |
5 Replies
6591 Views |
June 11, 2009, 04:22:00 pm by rob@vems.co.uk |
|
|
|
bootloader version
Started by Seight-v8 |
5 Replies
7182 Views |
February 07, 2013, 09:49:50 pm by Seight-v8 |
|
|
|
Avcs/vvti/vanos control problem
Started by Denmark |
5 Replies
7444 Views |
May 19, 2013, 05:51:45 pm by Denmark |
|
|
|
Vems v3 pnp Audi 3b sn nr u003986_A
Started by Skikar |
5 Replies
4495 Views |
May 07, 2018, 12:35:19 pm by gunni |
|
|
|
AIM on 2nd serial port now supported
Started by NOTORIOUS VR |
5 Replies
6585 Views |
October 03, 2016, 01:03:57 pm by Matus |
|
|
|
Need Help getting Mk2 vw tach working
Started by Psi4gti |
5 Replies
7835 Views |
October 29, 2012, 04:18:46 pm by Psi4gti |
|
|
|
ETC actuator is not moving
Started by Matus |
4 Replies
5211 Views |
July 10, 2016, 10:04:57 am by Matus |
|
|
|
always on anti lag
Started by davide |
4 Replies
3056 Views |
January 04, 2021, 04:44:59 pm by davide |
|
|
|
4 Replies
6050 Views |
November 03, 2013, 05:46:38 pm by VEMS |
|
|
|
|
wbo2_ri_target
Started by jeanno |
4 Replies
5855 Views |
December 13, 2012, 02:21:52 pm by GintsK |
|
|
|
4 Replies
6712 Views |
June 21, 2011, 10:57:04 pm by dnb |
|
|
|
|
Using a MAF (MASS AIR FLOW) with VEMS
Started by AVP |
4 Replies
6046 Views |
March 30, 2011, 08:58:08 am by AVP |
|
|
|
VE table TPS stuck on 5% instead of 0
Started by unariciflocos |
4 Replies
5699 Views |
May 03, 2014, 07:25:09 pm by unariciflocos |
|
|
|
4 Replies
7127 Views |
August 19, 2015, 08:46:45 am by VEMS |
|
|
|
|
4 Replies
6002 Views |
September 26, 2019, 07:09:20 pm by Seight-v8 |
|
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll