News:
When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
Subject  / Started by |
Replies / Views | Last post | ||
|---|---|---|---|---|
|
|
Round RPM input
Started by jonih |
0 Replies
7232 Views |
August 09, 2021, 05:32:55 pmby jonih |
|
|
|
Round Serial Number 144 Firmware upgrade?
Started by PeterSM |
0 Replies
5697 Views |
September 07, 2015, 05:48:20 pm by PeterSM |
|
|
|
Round V1 Gauge Fault
Started by Poloace |
1 Replies
7293 Views |
March 05, 2021, 03:40:21 pm by Poloace |
|
|
|
Round WB02 output as Vems 2nd wideband
Started by fphil |
4 Replies
8075 Views |
April 13, 2013, 11:10:19 am by fphil |
|
|
|
Round WBO2 EGT calibration problem
Started by kimmoz28 |
2 Replies
7382 Views |
October 13, 2012, 09:37:24 am by rob@vems.co.uk |
|
|
|
8 Replies
11068 Views |
June 26, 2009, 01:33:41 pm by kristjan |
|
|
|
|
RPM input from Audi S2 engine speed sensor
Started by ranz |
6 Replies
10041 Views |
November 02, 2008, 07:24:22 pm by ranz |
|
|
|
RPM problems
Started by eNcode |
4 Replies
6460 Views |
May 16, 2014, 05:37:31 pm by mattias |
|
|
|
RPM Reading Dropping Out
Started by blaze falconburger |
3 Replies
7490 Views |
June 10, 2009, 02:24:05 pm by ranz |
|
|
|
rpm signal from vems to vems guage?
Started by damo_S13 |
2 Replies
7352 Views |
May 03, 2008, 03:02:27 pm by damo_S13 |
|
|
|
RS13 - CA18DET Wiring
Started by Maff |
7 Replies
14299 Views |
March 20, 2008, 01:20:52 pm by Anu |
|
|
|
serious problems with gauge
Started by kekso22 |
10 Replies
15889 Views |
September 28, 2007, 09:27:16 am by rob@vems.co.uk |
|
|
|
Setting output mode for megasquirt use.
Started by paul f |
4 Replies
9536 Views |
July 30, 2007, 09:36:42 am by rob@vems.co.uk |
|
|
18 Replies
20365 Views |
August 24, 2015, 04:48:31 pm by Machismo |
|
|
|
|
setting up display-only round
Started by iwbs |
3 Replies
8974 Views |
August 10, 2016, 07:35:45 pm by iwbs |
|
|
|
2 Replies
8040 Views |
August 05, 2017, 02:40:27 pm by mr_g |
|
|
|
|
Setting up Round Display only gauge
Started by mdlimy |
4 Replies
8745 Views |
June 14, 2011, 05:21:24 pm by boostd audi |
|
|
|
Setting up the mulit-function gauge
Started by dkensk |
1 Replies
5866 Views |
June 07, 2014, 10:19:45 am by mattias |
|
|
|
Some Round problems
Started by Wolf_Tm |
2 Replies
6892 Views |
August 19, 2014, 10:37:23 am by Wolf_Tm |
|
|
|
Strange board temp reading
Started by M-Tech |
8 Replies
10620 Views |
October 31, 2007, 09:19:37 am by rob@vems.co.uk |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll