News:
When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
| Subject / Started by | Replies / Views  |
Last post | ||
|---|---|---|---|---|
|
|
Trigger Errors due to ignition coil
Started by Benzmac16v |
2 Replies
7723 Views |
June 10, 2011, 12:46:35 amby Benzmac16v |
|
|
|
20V NA 5 window dist. trigger
Started by nmerrill |
2 Replies
7638 Views |
January 10, 2019, 01:54:15 am by nmerrill |
|
|
|
Mitsubishi EVO 1-3 trigger supported?
Started by Ascona 400 |
3 Replies
7627 Views |
August 26, 2010, 03:40:01 am by rob@vems.co.uk |
|
|
|
secondary trigger timing
Started by silverliner |
4 Replies
7620 Views |
October 21, 2010, 07:34:11 am by silverliner |
|
|
|
36-1 crank wheel setup in VEMSTune
Started by qwkswede |
2 Replies
7605 Views |
February 27, 2010, 11:34:43 am by qwkswede |
|
|
|
Does this triggerlog look right? 1.8T AEB
Started by bonden |
3 Replies
7595 Views |
December 11, 2017, 10:42:17 am by bonden |
|
|
|
Secondary trigger HALL to vems, how?
Started by lost |
1 Replies
7581 Views |
August 14, 2011, 02:59:39 pm by Erikk |
|
|
|
advanced filter on 60-2 flywheel
Started by pug |
4 Replies
7578 Views |
December 15, 2016, 08:24:00 pm by fphil |
|
|
|
Audi ABH V8 pre-buy VEMS options
Started by taxman |
3 Replies
7557 Views |
December 16, 2017, 05:47:38 pm by Kamuto |
|
|
|
Trigger log correct interpretation
Started by Matus |
2 Replies
7461 Views |
July 16, 2016, 11:58:12 am by Matus |
|
|
|
1 Replies
7437 Views |
April 30, 2021, 08:22:34 pm by Kamuto |
|
|
|
|
36-1 hall rising edge
Started by Kamuto |
3 Replies
7391 Views |
December 08, 2013, 10:23:12 am by VEMS |
|
|
|
Hall to VR conversion
Started by M-Tech |
1 Replies
7336 Views |
January 01, 2008, 01:33:32 pm by rob@vems.co.uk |
|
|
|
2 Replies
7324 Views |
October 16, 2011, 07:04:51 pm by GTOBB |
|
|
|
|
3 Replies
7293 Views |
March 22, 2011, 08:40:04 pm by PG |
|
|
|
|
trigger errors w new unit
Started by ecutec |
2 Replies
7257 Views |
October 20, 2008, 12:05:49 pm by GintsK |
|
|
|
TDC after trigger min value
Started by z0tya |
2 Replies
7228 Views |
March 31, 2009, 02:04:09 am by rob@vems.co.uk |
|
|
|
cam sensor
Started by Seight-v8 |
3 Replies
7207 Views |
June 04, 2010, 06:59:57 pm by Seight-v8 |
|
|
|
VR to HALL
Started by beny1989 |
4 Replies
7168 Views |
January 05, 2017, 05:16:22 pm by beny1989 |
|
|
|
primery hall sensor problem
Started by andreNL |
2 Replies
7167 Views |
April 12, 2011, 07:39:46 am by andreNL |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll