News:
When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
| Subject / Started by | Replies  / Views |
Last post | ||
|---|---|---|---|---|
|
|
Launch Control
Started by Clio-wizard |
11 Replies
14883 Views |
June 14, 2011, 03:21:55 amby boostd audi |
|
|
|
EGT polarity
Started by BigD |
11 Replies
10047 Views |
July 12, 2010, 11:48:06 am by BigD |
|
|
|
Recommended configuration of outputs
Started by Manick |
11 Replies
9114 Views |
January 02, 2016, 12:52:49 am by Manick |
|
|
|
Output chanel Usage
Started by Sprocket |
11 Replies
10989 Views |
March 27, 2007, 02:01:58 pm by Sprocket |
|
|
|
11 Replies
8551 Views |
March 31, 2011, 05:56:12 pm by silverliner |
|
|
|
|
what cable to use
Started by ex-ctr |
11 Replies
14865 Views |
January 30, 2007, 07:11:20 pm by rob@vems.co.uk |
|
|
|
E85 0-5v input VEMS anytrim setup
Started by Scottme262 |
11 Replies
8750 Views |
August 16, 2017, 04:13:38 am by Scottme262 |
|
|
|
Burned box
Started by Taanhp |
11 Replies
6978 Views |
June 01, 2018, 09:38:06 am by Kamuto |
|
|
|
Display problem
Started by Lord_o21 |
10 Replies
9348 Views |
August 22, 2007, 09:01:20 am by Lord_o21 |
|
|
|
10 Replies
10185 Views |
March 10, 2010, 08:13:49 am by josh-stateside |
|
|
|
|
Vems install E12 M30B35 engine
Started by DMS |
10 Replies
12566 Views |
August 10, 2010, 08:51:10 am by DMS |
|
|
|
10 Replies
10009 Views |
September 29, 2010, 02:20:10 pm by z0tya |
|
|
|
|
Intermittant operation of P259 output
Started by dnb |
10 Replies
8229 Views |
June 11, 2009, 06:10:42 am by Bat |
|
|
|
A/C Support
Started by antonch |
10 Replies
13527 Views |
January 09, 2008, 09:02:25 pm by antonch |
|
|
|
Wideband gauge options for single sensor
Started by Ju1cE |
9 Replies
7356 Views |
September 22, 2015, 11:49:32 pm by NOTORIOUS VR |
|
|
|
analog input protection
Started by z0tya |
9 Replies
9722 Views |
February 02, 2010, 02:24:59 pm by z0tya |
|
|
|
Wideband Lambda Location in exhaust
Started by Sprocket |
9 Replies
9639 Views |
March 24, 2007, 04:18:20 pm by damo_S13 |
|
|
|
Shift cut input wiring ?
Started by mk123gti |
9 Replies
11285 Views |
April 02, 2015, 10:40:29 am by fphil |
|
|
|
VDO 0-10 bar 2 wire sensor calibration
Started by Wolf_Tm |
9 Replies
12107 Views |
October 05, 2017, 07:17:35 pm by Wolf_Tm |
|
|
|
Ground loop problem?
Started by dnb |
9 Replies
9496 Views |
August 24, 2007, 06:42:22 pm by cliffb75 |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll