When asking for technical help at the very least let us know the version of firmware you are running.
Cliff's Calibration (Mapping) Guide is a MUST READ: http://www.vemssupport.com/forum/index.php/topic,97.0.html
Subject / Started by | Replies / Views | Last post | ||
---|---|---|---|---|
No data on serial gauge
Started by Ju1cE |
1 Replies
4417 Views |
September 15, 2015, 02:40:41 pm by VEMS |
||
VEMS ETC Setup
Started by Brk97 |
2 Replies
4446 Views |
July 27, 2018, 03:26:29 am by jrussell |
||
VEMS Display USB-OTG cable connection
Started by Sprocket |
0 Replies
4457 Views |
October 02, 2017, 06:46:32 pm by Sprocket |
||
1 Replies
4457 Views |
April 18, 2018, 08:15:30 pm by gunni |
|||
0 Replies
4525 Views |
September 14, 2016, 03:42:57 pm by afterthought |
|||
LSX sensor wiring.
Started by NikolayN |
2 Replies
4527 Views |
August 03, 2014, 11:40:25 pm by gunni |
||
Bosch LSU 4.9 sensors
Started by Sprocket |
0 Replies
4538 Views |
October 02, 2017, 08:23:37 pm by Sprocket |
||
s14a 1997 pinout to Vems pinout.
Started by wwc_gang |
0 Replies
4554 Views |
October 03, 2015, 04:52:37 pm by wwc_gang |
||
vems v3 to s14a sr20det harness
Started by wwc_gang |
2 Replies
4561 Views |
September 14, 2015, 01:42:04 pm by wwc_gang |
||
1 Replies
4573 Views |
April 08, 2015, 08:36:35 am by VEMS |
|||
4 knock sensors.
Started by NikolayN |
1 Replies
4655 Views |
November 03, 2014, 11:35:47 am by VEMS |
||
Where to ground -> glassfiber buggy
Started by mads b (dk) |
1 Replies
4665 Views |
April 19, 2014, 11:07:40 am by VEMS |
||
Speed sensor (VSS) and speedo drive
Started by DButters |
2 Replies
4673 Views |
February 24, 2016, 09:14:30 am by Kamuto |
||
1 Replies
4707 Views |
April 08, 2022, 12:29:01 pm by Kamuto |
|||
onewire keepalive
Started by z0tya |
0 Replies
4716 Views |
June 14, 2012, 08:41:51 am by z0tya |
||
secondary trigger used for wheel speed?
Started by PG |
0 Replies
4721 Views |
May 01, 2011, 11:00:23 am by PG |
||
Basic Loom Qs (12v source)
Started by Tom |
2 Replies
4733 Views |
February 24, 2010, 03:43:42 am by Tom |
||
Mcp3208 probably fried, but why?
Started by Razkin |
2 Replies
4737 Views |
August 04, 2015, 11:13:09 am by Razkin |
||
New loom questions
Started by reevio |
0 Replies
4751 Views |
December 29, 2011, 07:14:57 pm by reevio |
||
MAT Sensor
Started by se7ensport |
1 Replies
4752 Views |
September 13, 2011, 07:12:25 am by z0tya |
Normal Topic
Hot Topic (More than 15 replies)
Very Hot Topic (More than 25 replies)
Locked Topic
Sticky Topic
Poll